Re: What have you done to your Scooter today?
Posted: Sat Mar 29, 2014 7:40 pm
Fitted my fender extender, as it fell off ages ago. Hope the tiger seal holds it. Lubed the chain. Filled up.
https://www.maxi-muppets.co.uk/forum/
What have you done to your Scooter today?
Page 82 of 232
Re: What have you done to your Scooter today?
Posted: Sun Mar 30, 2014 8:08 pm
Did 190 miles to the Ace and back.
Re: What have you done to your Scooter today?
Posted: Thu Apr 03, 2014 11:29 pm
Changed to the shorter sport screen. Yet again.
On the move with Tapatalk
On the move with Tapatalk
Re: What have you done to your Scooter today?
Posted: Fri Apr 04, 2014 12:30 am
Put two new Mirrors on the GTS 250ie 
Raven
Raven
Re: What have you done to your Scooter today?
Posted: Fri Apr 04, 2014 1:17 am
I just slide mine DOWN!MjW wrote:Changed to the shorter sport screen. Yet again.
On the move with Tapatalk
Re: What have you done to your Scooter today?
Posted: Sat Apr 05, 2014 6:37 pm
Fitted new bearing to the swinging arm plate thing. Wife was a bit miffed when I baked it in the oven for 10 minutes at 200 degrees! 
Then I took the Dr Pulleys out and put OEM rollers back in and then fitted new front pads and gave it its bi-annual wash!
Then I took the Dr Pulleys out and put OEM rollers back in and then fitted new front pads and gave it its bi-annual wash! Re: What have you done to your Scooter today?
Posted: Sat Apr 05, 2014 9:20 pm
Fitted the panels that ive been waiting for months. Also did an oil change and a quick was to finish. Ready now for the trade in!!
Sent from my ME173X using Tapatalk
Sent from my ME173X using Tapatalk
Re: What have you done to your Scooter today?
Posted: Sun Apr 06, 2014 6:25 pm
Fitted mudflap to the Silverwing using Meldrew's idea of a cut down flower pot and I am pleased with the result.
Thanks Meldrew.
Next job is to fit the Acerbis hand guards which rely only on compression inserts in to the end of the handle bars for fitting. On attempting to mount on the Honda I find that the bars are not hollow and the guards foul the screen on full lock. Which is disappointing as I found they worked well with the heated grips, drastic modification maybe required.
Thanks Meldrew.
Next job is to fit the Acerbis hand guards which rely only on compression inserts in to the end of the handle bars for fitting. On attempting to mount on the Honda I find that the bars are not hollow and the guards foul the screen on full lock. Which is disappointing as I found they worked well with the heated grips, drastic modification maybe required.
Re: What have you done to your Scooter today?
Posted: Sun Apr 06, 2014 7:10 pm
Fitted a new/used exhaust on the GTS 250ie
Raven
Raven
Re: What have you done to your Scooter today?
Posted: Sun Apr 06, 2014 9:52 pm
ollie wrote:Fitted mudflap to the Silverwing using Meldrew's idea of a cut down flower pot and I am pleased with the result.
Thanks Meldrew.
Next job is to fit the Acerbis hand guards which rely only on compression inserts in to the end of the handle bars for fitting. On attempting to mount on the Honda I find that the bars are not hollow and the guards foul the screen on full lock. Which is disappointing as I found they worked well with the heated grips, drastic modification maybe required.
If you remove the grips you will find a couple of holes 20mm or so from the ends, press the ;little tabs in with a diddy screw driver and pull out the inserts..
PS: i don't no what they are like on the Wing but they could be 6 or 7 inchs long