What have you done to your Scooter today?

pikey · Post by **pikey** » Mon Sep 07, 2015 3:52 pm

Get vee rubber can't knock a nail in they are that hard .Can't wear them out Bob says

Post by **kayz1** » Mon Sep 07, 2015 4:42 pm

ordered a pair of tyres for the Pegaso to get it off my bike table, another two Stilh saws to do today plus go to the dealers for bits.

Deleted User 4154 · Post by **Deleted User 4154** » Mon Sep 07, 2015 4:46 pm

pikey wrote:Get vee rubber can't knock a nail in they are that hard .Can't wear them out Bob says

Theirs were still the cheapest when I ordered my new Conti. True I probably wouldn't have got a puncture, but I'd most likely be in a hedge somewhere between here and Shell Island

pikey · Post by **pikey** » Thu Sep 10, 2015 4:17 pm

Just been in garage started the Vespa up poor neglected and abused thing it is .Found plug spanner to change plugs on the Panda it's got those small ones in .

Post by **maxiscoot nz** » Thu Sep 10, 2015 4:43 pm

keep riding the cn

pikey · Post by **pikey** » Thu Sep 10, 2015 6:37 pm

Wife prefers Vespa and I'm torn between riding Vespa in St Tropez at Vespa rally or riding the cn in Normandy with the Ugly Bunch .Tough decision can't do both .

Post by **phil y** » Thu Sep 10, 2015 7:47 pm

Rode mine up the east coast to Whitley Bay

Post by **kishan** » Fri Sep 11, 2015 10:58 pm

fitted blue coated filament bulbs filled with xenon and halogen gas to replace my blown led side light bulbs

Post by **kayz1** » Sun Sep 13, 2015 2:46 am

Pulled the motor out of the 650burger, ripped the clutch and CVT out of it for a long look at.. Primary shaft is cooked along with the primary drive gear/bearings/seals..P gear bearings are a complete motor strip to get at them so it will be up to the dealer if they want me to do it...Rear wheel
bearings are knackered also.. It has defo been apart before as a few internal parts are marked and one or six new bolts fitted where it is only possible to reach them when the CVT is out...in short it is a cock up by some body in-order to get rid of...I'm not paying for it though

the primary pulley had been put back in with out the correct shims, so lots of metal to metal contact has occurred

priced a Suzuki oil seal for the CVT at Ãƒâ€šÃ‚Â£38

they must be having a laugh

Ãƒâ€šÃ‚Â£9 delivered from simply bearings.. 24.95p for a clutch cover gasket from Suzuki WEMOTO price Ãƒâ€šÃ‚Â£ 13

After all this no indication as to why it was lugging at 60mph getting red hot, well not from inside anyway...so i went back to basics and yes the thermostat is stuck closed

I did ask what they wanted me to do honest

No fault codes recorded as they dropped it off with the battery out of it.

i am betting it was over heating and the ECU was putting it into limp home mode...we will see after i get it back together..
a good days work me thinks.
Lyn.

Post by **Cookie** » Sun Sep 13, 2015 3:01 pm

Blimey! That's a bit of work there eh Lyn?
It's always more of a pain following up where someone else has already had a go!
Good luck with it.

What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?

Re: What have you done to your Scooter today?